935CA

Wall control or outdoor dropped off the bus.

1. 1 Data pair, not 24 V

   On Bryant 935CA indoor/outdoor comm is a data pair (AB, S1/S2, U, ComfortBridge, ComfortLink — whatever THIS plate uses). It is not a 24 V Y. Check polarity, continuity, and that nobody landed it on R/C. A/B/C/D landing, polarity, only one Infinity control, no 24V on D.

   Expect: Pair continuous, not shorted to chassis, polarity per the diagram.

2. 2 Power both ends, then the outdoor status

   Indoor transformer and outdoor control both alive. Read the outdoor LED / 7-seg. Water in the outdoor control is the usual dead-end after a storm. C present. A 24V Performance stat on this IFC will not stage it like a 59TP6.

   Expect: Both controls powered. Outdoor showing a comm or address state, not a blank board.

3. 3 Address / bias, then the control

   Communicating plates need a matching indoor address and sometimes a terminating bias. Swap is last: known-good pair + power both ends + correct address. Outdoor pair on the same bus — a dead Greenspeed looks like indoor comm loss until you read events.

   Expect: Indoor sees the outdoor. No comm code after a power cycle.

24 V fuse on the IFC.

1. 1 Find the 24 V short before you replace the fuse

   On Bryant 935CA an open IFC fuse is a short on W, Y, G, HUM, EAC, or a data pair landed on 24 V. Unplug the thermostat / data harness first. HUM/EAC, valve harness, or 24V landed on ABCD.

   Expect: Fuse out. 24 V transformer still good. Harness isolated.

2. 2 Replace the fuse with the harness off

   New fuse, harness still off. If it holds, the short is in the field wiring or accessory. Plug one circuit back at a time (W, then Y, then HUM/EAC). Replace fuse only after the short is gone.

   Expect: Fuse holds with harness off. Dies when the shorted lead lands.

3. 3 If it blows with the harness off

   Short is on the Bryant 935CA IFC or the gas-valve harness. Unplug the valve and try once more. Repeat blow with valve unplugged = IFC.

   Expect: Do not keep feeding fuses into a welded valve coil or a burned IFC trace.

Two-stage draft path. 31 is the active-stage / draft prove; 32 is low-fire PS. Unlike 59MN7, these are discrete switches.

1. 1 Prove inducer and the live code

   Do not pull power — that clears the Bryant 935CA active code. Write 31 / 32. Is the inducer spinning on this call? Silent inducer is not a pressure switch. Two hoses, two switches. Do not treat this as a modulating band.

   Expect: 120 VAC at the inducer on a heat call. Wheel turning.

   If fail: 120 VAC missing → IFC / door switch / incoming power. Voltage + dead motor → inducer.

   If pass: Inducer running + this code → trap, hose, switch, vent (step 2).

2. 2 Trap, collector, and the hose

   A drowned 96% trap will not make collector pressure. Pull the trap, flush it, confirm the collector box and inducer outlet are not full. Hose cracked, off the port, or full of water fakes an open switch. 32 = low-fire hose, low inducer, attic PVC/trap/wind.

   Expect: Trap flowing, hose dry and downhill, ports not swapped on a two-switch board.

3. 3 Switch ohms, then vent load

   Ohm the pressure switch: NO, must close when that inducer speed is making the collector setpoint. If the switch is good, walk the PVC — bird screen, ice, long 2" run, wind, shared chase. High-fire prove fail is the high PS, not a 59MN7 42 band story.

   Expect: Pressure switches: Two discrete switches. 32 = low. High-fire has its own hose. Not an MN7 band.

   If fail: Replace the open switch only after the vent and trap are proven.

   If pass: Switch closes on draft and the code stays → IFC input.

Airflow or flame-containment. 13 is the hardened 33.

1. 1 Treat this as flame outside the exchanger

   Do not reset the Bryant 935CA rollout and walk away. Write the code, kill the call, and look for flame at the burners, crossover, and vestibule before you do anything else.

   Expect: No flame outside the exchanger. Burners seated. Crossover lit.

   If pass: Still inspect secondary / flue / condensate before you reset.

2. 2 Secondary, condensate, and flue

   Blocked secondary, drowned collector, or a plugged flue pushes flame out the front. Pull the inducer/collector look, confirm the trap is flowing, and check PVC/vent. Infinity heat CFM, filter, coil, return. Not a 59SC5 heat tap and not a 59TP6 model plug.

   Expect: Dry collector, open flue, trap clear.

3. 3 Reset only after the cause is fixed

   Manual-reset rollout. Recurring rollout on Bryant 935CA is a CO / fire call — cracked primary, misaligned burners, or a failed secondary. Confirm CO in the space before you leave. Rollout is manual reset — inspect exchanger first.

   Expect: One clean cycle after the cause is fixed. No second reset as a repair.

Trial without flame sense. 14 is the hardened 34.

1. 1 Measure µA while it is running

   Do not clean first and guess. Series-µA the rod on Bryant 935CA during a call. Falling µA is oxide, ground, or a dying flame. A hard drop is often the pressure switch or limit opening, not the rod. HSI, gas, rod, ground.

   Expect: Flame sense: µA per 59TN6 / 986T door card.

2. 2 Rod, ground, then gas

   Clean the rod with a non-scratch pad — not sandpaper. Chassis ground to burner box and IFC (painted screw and missing star washer are classic). Then manifold on the stage that is dropping and confirm LP conversion leftovers. If 32 is also stored, fix low-fire draft before you condemn the igniter.

   Expect: Manifold on the rating plate. Solid burner-box ground.

3. 3 Prove it is not a switch opening

   Watch the live Bryant 935CA display when flame drops. A PS or limit code that appears at the drop means the rod was a victim. Inducer, hose, vent wind, or a limit on a wrong heat tap.

   Expect: µA stable and the live code stays a flame code — then rod/valve/IFC. Otherwise chase the new code.

Infinity VS motor not at commanded CFM.

1. 1 Is the wheel free?

   Spin the Bryant 935CA blower by hand. Ice, debris, or a seized bearing is not a control problem. Confirm the motor type on this plate — serial ECM, 9-speed tap, or X-13 — before you grab a capacitor. Static, wheel, serial harness, Infinity indoor size / CFM setup.

   Expect: Wheel free. Correct motor family for this IFC.

2. 2 Command vs rotation

   Call for G or heat and confirm the IFC is actually requesting CFM (taps, serial, or communicating). Amp the motor. Locked rotor + a good command = motor. No command = IFC / harness / shared data. Filter and coil.

   Expect: Command present. Motor amps in range, not locked.

3. 3 Static and the wrong motor

   High static will trip current/limit codes and look like a dead motor. Measure TES vs this cabinet. Wrong horsepower or a leftover memory card after a control swap is the other half of this call.

   Expect: Static on the blower chart. Matching motor / shared-data card.